Wire liveHOMEFLOW bureau · all times UTC · copy moves as filed
FiledHOMEFLOW · NOV 20, 2026, 16:12

What to Check Before Scheduling a Home Inspection

Buying or selling a home is a process with a lot of moving parts. One of the most important steps is the home inspection, and a big part of that inspection involves the plumbing. A home that shows well and has no hidden water issues will not only pass inspection more smoothly but also give buyers confidence. Getting ahead of problems before the inspector arrives can save time, money, and negotiation headaches. A good place to start is making sure your accessible shut off valves are in working order and that every part of the system is ready for a thorough look.

Inspectors check for leaks, code compliance, and general condition. They want to see that the system has been maintained and that there are no surprises behind walls or under sinks. By running through a simple set of checks beforehand, you can identify small issues early and address them. This article walks through the key points to verify so your home is ready for its close-up.

Start with the accessible shut off valves

The first thing many inspectors look at is whether the main water shut-off valve and the individual fixture shut-offs are easy to reach and operate. If a valve is stuck, rusted, or hidden behind stored items, it is a red flag. An accessible shut off valve that turns freely and shuts off water completely is a basic requirement for any home. Test each one you can find. If any valve is hard to turn or does not stop the flow, have a plumber service or replace it before the inspection.

Beyond the main valve, check shut-offs for the toilet, the sinks, and the washing machine. These are the ones you would use in an emergency. If they are buried under cabinets or behind a panel that needs tools to open, consider installing an access panel or repositioning the valve. Inspectors note this as a safety and convenience issue. Having all your accessible shut off valves in plain sight and working order sends a clear message that the home has been cared for.

Look for leak evidence everywhere

Leaks can be obvious or sneaky. Start with areas that are easy to see: under every sink, around the toilet base, at the water heater connections, and along exposed pipes in the basement or crawl space. Look for stains, drips, corrosion, or dampness. Even a small water stain on the cabinet floor under a sink can signal a past leak that may or may not be fixed. Inspectors will check these spots with a flashlight and a moisture meter.

Don't forget less obvious places. Check around the washing machine hoses, the dishwasher supply line, and the refrigerator ice maker connection. These flexible hoses can develop pinhole leaks or burst over time. If any look old or cracked, replace them. Also inspect pipe transitions where different materials meet, such as copper to galvanized steel, or plastic to metal. These joints can corrode or fail due to electrolysis. A plumber can advise on proper dielectric unions or transition fittings if needed.

Verify code compliance for key items

Homes built to different codes may have quirks that don't meet current standards. Inspectors note anything that is not code compliant, even if it was acceptable when installed. Common issues include missing pressure relief valves on water heaters, improper venting for gas appliances, or the lack of an expansion tank. If you are unsure about any of these, call a professional for a quick assessment.

Also check that all shut off valves are installed in the correct orientation and that none are blocked by drywall or cabinets. An accessible shut off valve that is behind a wall with no access panel is effectively useless. The same applies to valves that are located too high or too low to reach without a ladder. Having everything within easy reach and properly installed shows that the home has been maintained to a good standard.

Test the water pressure and temperature

Turn on the hot and cold water at every fixture. The flow should be steady, and the water should heat up within a reasonable time. Low water pressure can indicate a partial blockage, a bad shut-off valve, or a pipe problem. If a fixture has low pressure, check the aerator for debris first. If that doesn't fix it, the issue may be deeper in the system.

Temperature is another check. At the water heater, make sure the thermostat is set to a safe temperature, usually around 120 degrees Fahrenheit. Too hot can scald, too cool can allow bacteria growth. Also test the water in the shower and at the kitchen sink to ensure it gets hot quickly. Slow heating can mean a failing water heater or a problem with the circulation system.

Check the water heater and its surroundings

The water heater is a major piece of equipment. Inspectors look at its age, condition, and installation. If it is more than 10 to 12 years old, it may be near the end of its service life. Look for rust on the tank, corrosion on the fittings, or any signs of leakage around the pressure relief valve. The pressure relief valve should have a discharge pipe that goes to a drain or outside, not just drip onto the floor. Also check that the gas or electrical connections are sound and that the unit is properly vented if it is gas.

If the water heater is in a closet or a small room, make sure the area is clear of clutter and that the access panel is easy to open. The inspector will want to see the unit's data plate and check the temperature and pressure settings. A clean, well-maintained water heater with a recent service record is a big plus.

Inspect the visible pipework

Look at the exposed pipes in the basement, attic, or under the house. Check for signs of corrosion, especially at joints and around hangers. Pipes should be properly supported, not sagging or resting on other pipes. Also check for any signs of previous repairs that look like temporary patches. A properly installed pipe system with clean joints and no leaks gives confidence that the home has been well cared for.

Pay attention to the pipe transitions mentioned earlier. Mixing metals without proper isolation can cause galvanic corrosion. If you see a copper pipe connected directly to a steel pipe, that connection may fail over time. A good plumber can install a dielectric union to prevent this. Similarly, check that any plastic pipes are not exposed to sunlight or extreme temperatures, as that can degrade them.

Make sure the inspection contingency is manageable

In a real estate transaction, the inspection contingency is the period during which the buyer can ask for repairs or back out. Having a home with plumbing systems prepared for inspection means fewer surprises for everyone. If the inspector finds only minor issues, the process moves quickly. If major problems surface, the buyer may ask for a large credit or even walk away. Spending a little time and money on pre-inspection maintenance can prevent that.

You want the inspection report to show a house that is ready to move into, not one that needs immediate work. A thorough check of the accessible shut off valves, the water heater, and all visible pipes goes a long way toward that goal. When you have plumbing systems prepared for inspection, you shorten the negotiation time and build buyer trust.

Don't forget the basics

Finally, do the simple things that are easy to overlook. Clear out under-sink cabinets so the inspector can see the pipes and shut off valves. Make sure the water heater closet is tidy and that the access panel is not blocked. Run each faucet and flush every toilet to confirm they work correctly. Look for any drips or running sounds after the fixtures are turned off. A toilet that runs intermittently can be a simple fix but will show up on an inspection report as a defect.

Take a few minutes to check for any signs of moisture on the walls or ceilings near plumbing runs. A water stain on the ceiling below a bathroom is a clear signal of a leak. If you find one, investigate and fix it before the inspector arrives. It is much better to address it yourself than to have the inspector flag it and raise questions about the condition of the entire system.

Preparing your home for a plumbing inspection does not have to be complicated. It mainly involves checking that everything is in working order, that all accessible shut off valves are easy to reach and function properly, and that there are no hidden leaks or code violations. A little effort upfront makes the inspection day go smoothly and puts everyone in a better position to close the deal.

Ends · HOMEFLOW